Affiliate Disclosure: When you buy through links on our site, we may earn an affiliate commission at no cost to you.

Chainsaw Mill Guide – Everything You Should Know

If you don’t know how to work with a chainsaw mill, you don’t need to buy a chainsaw mill. But if you have one, it is better you use it for saving your money!

Today, we have come up with an amazing chainsaw mill guide that will teach you the basics. Even if you are a pro, you can learn the secrets of cutting wood perfectly!

Let us have a look at the step by step process of chainsaw mill woodcutting!

Step by Step Chainsaw Mill Guide

Step 1 – The Preparation

First of all, you have to get ready for using a chainsaw mill. Not only the beginners but the pro users can get themselves into danger if they do not prepare right for using this device.

Always remember that when you work with a blade, you have to cover yourself as much as you can. Safety gears are the first duty you have to follow. Go for thick gloves to keep your hands safe.

Goggles can be highly beneficial too. It is better you cover your hands and legs with long-sleeved dresses and full pants.

The shoes you will use in the process should be sturdy enough to keep your feet protected from the blade. Also, never work alone.

Keep someone for your aid. If someone else does the work of moving the wood, the chances of any unwanted accidents will no longer be so prominent.

Before you start, bring the fuel you need. For measurement, you will surely need tape measurement if you want to be perfect with the cuts. Keep it beside you. Also, keep a chainsaw sharpening kit around you.

Step 2 – Starting the Initial Cutting

Whenever you buy it, make sure you get a perfect chainsaw mill. It will afford you sharp cuts and quick operation.

In the case of cutting with a chainsaw mill, first of all, you have to check the rails. We all know that in most cases, when we work with a chainsaw mill, we settle for a rounded top log.

And if the case is the same for you, you have to set the slabbing rails at a perfect height. If the height is not perfect, you might not get the precise cuts you are aiming at.

When you set it, ensure that the rails extend and cross the log’s ends. As a result, the cut will get support for it throughout the cutting process.

Before you begin to work, you have to observe the log. Note down about the features that you like to keep. After this, you have to go for the first cut.

Make sure you are very careful when you do your first cut. When you are done with it, you can easily remove the slabbing rails.

Step 3 – Preparing the Second Cut

After you have done the first thing perfectly, you have to move to the next one. The first one is a guide to the next cuts.

The previous cut will easily help you do the following cuts comfortably. And this is the reason we told you that the initial cut is the most important cut in this chainsaw mill guide.

When you are up for making beams, you have to settle for a cut on the log’s bottom part. The same thing goes for other lumber.

If you are cutting in general, these are enough for you. You can get almost complete lumber after this cut.

There are some advantages in this process. You can start the process exactly where the tree fell! After that, you have made the whole cut perfect in some other place.

There, you can use other tools so that you can get more precise cuts.

As there are other tools that can provide you with cleaner and sharper cuts than chainsaws, we recommend you to use them after you are done with this second cut. For a slimmer kerf, you can use bandsaw too!

Step 4 – The Final Cut

No, people don’t usually use chainsaw kill to finish the lumber. But if you are the one who wants to do it, you can also do it!

For this, you have to get your hands on the slabbing rails once again. This will help in guiding the chainsaw! it is always better to settle for a carpenter’s square.

This will certify that you are getting 90-angled crisp! And if you get it, you are almost done! Now, you can easily transform the log into boards.

As we have told you, the previous cut will be your guide and you can work accordingly!

Pro Tips for Using Chainsaw MillChainsaw mill uses

  • Don’t panic. Go for a slow start and stop the cut in a slow motion. The cuts will be cleaner and better!
  • When you are up for straight cuts, you can use the slabbing rails. These are the right guides for all the cuts you go for!
  • When you are using a chainsaw mill, there will surely be dust. If you think that slowly cutting will not invite the wood dust, you are wrong.

So, to keep your eyes safe, you must cover them. Also, make sure you are not inhaling the dust as it can be harmful.

Pick up a dust mask to keep your lungs safe! Getting the whole body covered is most probably the best idea you can follow.

  • When you stop between cuts, your cut gets a little out of the line. You don’t want to make a straight cut curved.

And so, we recommend you to fill up the whole tank with fuel; at least as much as you can, fill it up. It will reduce the chances of stopping while cutting and keep the cutting process smooth.

  • As we have said, you don’t want to ruin the straight cut and so, you must not stop, we are again telling you to stop!
  • Yes, you must give your machine some time to cool down. And for this, when you are done cutting a straight line, rest a bit. You don’t need to switch it off.

All you have to do is give it a rest from cutting for a few minutes. Also, don’t forget to give yourself a bit of a break!

Wrap Up

We know it is not easy to use a chainsaw mill. But this chainsaw mill guide will help you a lot in cutting wood the way you want!

You don’t need to be a pro while doing this. All you need to do is follow the basic rules along with the tips.

Have a look at the steps and do it alone! Share your funny stories about cutting with a chainsaw mill! Comment below!

Read More

About Jose Wilson

Hi, I am Jose Wilson. I am an avid DIY woodworker. I love to try out new woodworking tools. In over 6 years I have tried several wood working tools including circular saws, table saws, chain saws, and jigsaw among the rest. My inspiration came from watching my dada work. I also learned that many people didn’t quite understand how to use these tools. Today, I have helped so many people to learn the use, benefits, and how these DIY woodworking tools operate. I have created a number of work-tools related posts, built websites, and developed social media pages. Follow me here to learn more.

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts