The Husqvarna 572 XP can be the best choice for forestry and tree care professionals even in the toughest environments. This chainsaw model has a 12% higher cutting capacity than previous models. It’s true that problems with the 572 XP chainsaw are rare. Nonetheless, you may have to face some minor problems while operating this chainsaw.
Notable among these problems are starting problems, bogs out when it gets hot, oiler issues, leaking oil or gas, and more. Although these are minor problems and can be fixed quickly, if you don’t solve them at the right time, it will ruin your work continuity.
In this article, I am going to discuss in detail some common problems with the Husqvarna 572 XP chainsaw model and its solutions. The discussion will help you get your chainsaw back in working order as quickly as possible.
Anyway, before starting the troubleshooting phase I would like to briefly discuss the technical specifications and interesting features of the chainsaw. This will give us a better idea of the 572 XP chainsaw model.
Husqvarna 572 XP Problems and Fixes: Quick Table
This quick table will be very helpful for experienced chainsaw users. Especially for those who can catch the causes of chainsaw problems.
| Husqvarna 572 XP Problems | Fixes |
|---|---|
| Trouble with starting | Clean the carburetor thoroughly. Check the spark plug and air filter, and clean them if dirty. |
| Bogs out when it gets hot | Open the vent holes by cleaning the fuel cap. Clean the fuel filter, fuel lines, and carburetor thoroughly. Check the spark plug and air filter for dirt buildup. |
| Oiler issues | Clean and adjust the oiler. |
| Autotune problem | Reset autotune. |
| Suddenly won’t start | Check fuel level, spark plug, and air filter. Clean and adjust the carburetor. |
| Running roughly | Make sure the guide bar and chain are lubricated properly. Clean the air filter, carburetor, and spark plug, replace them if necessary. |
| Producing excessive smoke | Use fuel and oil mixture in correct ratio and clean the air filter. If the chain is tight, loosen it as needed and check for proper lubrication. |
| Leaking oil or gas | Replace fuel and oil line. |
| Starter rope not working | Apply lubricant between the rope rotor and housing. |
9 Common Husqvarna 572 XP Problems and How To Fix Them Quickly
Here I am going to discuss the common problems and solutions of the Husqvarna 572 XP chainsaw in detail. Even if you have little experience with chainsaws, you can still maintain your continuity of work by following these guidelines to solve common problems with your chainsaw.
Problem 1: Trouble With Starting
Starting problem is a common issues with chainsaws. This problem can occur with any chainsaw, and the Husqvarna 572 XP is no exception. Although these chainsaw models have advanced features to make the starting process easier, you may still experience starting complications at times.
Cause:
Many factors can be responsible for starting problems. However, this problem is usually caused by carburetor problems, dirty air filters, and spark plugs. Old or low-quality fuel is also one cause of starting problems.
How To Fix:
To solve the starting problem, you need to cleanse the carburetor and fuel lines to remove any blockages. You can use a carburetor cleaner spray for better cleaning. Check the spark plug and air filter, and clean them if dirty. Replace them if they are too old. You can avoid this problem by using quality fuel as per the recommended ratio.
Watch the video below to know how to clean the carburetor properly.
Problem 2: Bogs Out When It Gets Hot
Many users complain that Husqvarna 572 XP chainsaws bog out when they overheat. This is quite an annoying problem because once the chainsaw heats, you have to stop working for quite some time.
Cause:
Many factors can be responsible for this problem as well. But one reason is that the vent holes of the fuel cap are closed. Also, overheating because of a failed carburetor divider, dirty fuel line, fuel filter, or a dirty carburetor can also be to blame.
How To Fix:
Clean the chainsaw’s fuel cap thoroughly and make sure the vent holes are not blocked. Wrap the carburetor divider with thermal reflective tape. Also clean the fuel filter, fuel lines, and carburetor.
Problem 3: Oiler issues
Chainsaws become difficult to operate if the guide bar and chain are not lubricated. Dry guide bars and chains are one cause of kickbacks. Operating the chainsaw in this condition will quickly wear down the chain. If the chain is over-lubricated, it wastes oil.
Cause:
Clogged well holes, obstructions in oil lines, malfunctioning oilers or other parts of the system, and misalignment are usually the cause of this problem.
How To Fix:
Clean the oil filter, oil hole, and oil line thoroughly. Observe the oiling system and take necessary action if there is any problem. Adjust the oiler properly and pay close attention to chainsaw cleaning.
You can also check the short video below to solve the Husqvarna 572 XP chainsaw oiler issue.
Problem 4: Autotune issues
AutoTune is a prominent feature invented by Husqvarna that automatically adjusts the chainsaw to any weather and job requirements. There are also complaints about this feature not working properly at times.
How To Fix:
To fix this problem, you need to reset AutoTune. To reset, run the chainsaw at full throttle with the chain touching the top of a log. At first, the chainsaw’s rpm will rise slightly, but after 30 to 40 seconds it will continue to run at a fixed rpm and the AutoTune feature will reset.
The video below can also guide you in this regard.
Problem 5: Suddenly Won’t Start
Have you ever tried to start a chainsaw but it won’t start? As can be the case in harsh weather, some problems with chainsaws can also be to blame.
Cause:
A dirty spark plug or air filter can cause this problem. Also, if there is an obstruction in the fuel from the carburetor to the combustion chamber, the chainsaw will not start.
How To Fix:
First, check whether the fuel level of the chainsaw is correct or not. If the chainsaw does not start, it is wise to replace the spark plug and air filter. Also, clean and adjust the carburetor. If there is any blockage in the oil line, clear the blockage.
Problem 6: Running Roughly
A chainsaw becomes a bit difficult to control if vibrates excessively or runs rough. Moreover, it is very difficult to operate the chainsaw for a long time with this problem.
Cause:
Usually, this type of problem occurs in chainsaws if the guide bar and chain are not lubricated. If there is a problem with the air filter, carburetor, or spark plug, the chainsaw cannot run smoothly but is rough.
How To Fix:
Check the oiler and ensure that the guide bar and chain are being lubricated. Clean the air filter and spark plug, and replace them if necessary. Clean and adjust the carburetor.
Problem 7: Producing Excessive Smoke
Excessive smoke from a chainsaw can intimidate a novice operator. Anyway, there is no reason to worry. This is not a complicated problem and you can fix this problem easily.
Cause:
A dirty air filter obstructs air flow and can cause excessive smoke. Even with high oil content in the fuel, the chainsaw produces extra smoke. If the oiling system is not working, we often see smoke in the guide bar and chain area.
How To Fix:
Clean the air filter, and replace it if necessary. Use standard fuel and oil mixture as per the company-recommended ratio. Adjust the idle speed of the chainsaw if it is high. Examine the oiling system if smoke from the guide bar and chain and take necessary action. Sometimes the exhaust system gets clogged with dirt and creates smoke. Clean the exhaust system properly.
Problem 8: Leaking Oil Or Gas
You can understand if a chainsaw is leaking gas or oil. Left in this condition, the bottom surface of the chainsaw gets wet. If there is a fuel leak, you will get a musty fuel smell from the surface, while an oil leak rarely smells that much.
Cause:
Over time, fuel lines or oil lines get old and crack and leak. Even if the oil hole in the guide bar is clogged with dirt, oil leakage may occur.
How To Fix:
Replace the fuel line to fix the fuel leakage. Note that each attachment is correct. To fix oil leakage, replace the oil line as well as thoroughly clean the oil hole in the guide bar.
Problem 9: Starter Rope Not Working
Problems such as a starter rope not working are less common, but some Husqvarna 572 XP users have complained. Here, the starter rope usually takes a long time to re-compress or does not go in all the way. This is not a complicated problem and is easily fixable.
Cause:
Sometimes this problem occurs when the cord sticks out on the rope rotor or the rope rotor sticks tightly with the housing.
How To Fix:
Open the side cover of the chainsaw and check if the cord comes out of the rope rotor. If it comes out, twist it again in the right way. Apply lube between the rope rotor and housing.
The video below may also help you. Although a Stihl chainsaw’s starting rope problem is solved here, the process will be the same for the Husqvarna 572 XP.
Technical Specifications & Interesting Features Of Husqvarna 572 XP
That the Husqvarna 572 XP chainsaw model is extremely powerful and convenient is evident from its specifications and features. Medium to large, its features are ideal for any task.
Technical Specifications
- Power source: Gas
- Displacement: 70.46 cc
- Power output: 5.8 hp
- Idling speed: 2,700 rpm
- Maximum speed: 9,900 rpm
- Powerhead weight: 14.5 lbs
- Recommended guide bar length: 15-inch to 28-inch
- Fuel tank capacity: 710 ml
Interesting Features
- State-of-the-art filtration system: Chainsaws are equipped with heavy-duty filters to ensure longer and better filtration through a larger filtration area than other models. As a result, you can operate the chainsaw for a long time without cleaning the air filter again and again.
- Low vibrations: Chainsaws come with an anti-vibration system. The feature helps protect the body as well as reduce fatigue and increase productivity.
- Optimal chip ejection avoids clogging: The Company has designed an optimized clutch cover, which ensures ejection and effectively prevents clogging even when cutting long wood fibers.
- Rubber handle inlay for a safer grip: The rubber handle helps ensure a firm and secure grip.
- Air Injection filters 98% of incoming dust: This is a feature that removes up to 98% of incoming dust before it reaches the filter. As a result, the air filter requires relatively less work and can provide higher efficiency.
- AutoTune: This is a dominant feature invented by Husqvarna that keeps your chainsaw at peak performance in any situation. This feature works to adapt the chainsaw to any type of weather condition or job.
- Magnesium crankcase: The magnesium crankcase makes the chainsaw more suitable for high rpm and tough professional use.
- Smart Start Technology: This feature helps the chainsaw start with minimal effort.
Tips To Take Care Of a Husqvarna 572 XP
A chainsaw needs regular care in order to use it for a long time or to maintain its performance. Here I am sharing some tips that you can follow to keep your Husqvarna 572 XP chainsaw at peak performance for a long time.
- Clean the chainsaw regularly. Whenever you store it after finishing your task, be sure to clean it thoroughly.
- Clean the air filter and spark plugs regularly and replace them at regular intervals.
- Always use the fuel and oil mixture as per the company-recommended ratio.
- A spark plug can fail at any time, so always carry a spare.
- Always keep the chain sharp to get the best cutting performance.
- Clean and adjust the carburetor occasionally.
- If the chainsaw needs to be stored for an extended period, drain all fuel.
Pros And Cons Of a Husqvarna 572 XP
The Husqvarna 572 XP is a professional quality chainsaw that comes with many features. You can use them for any kind of wood-cutting task with no hassle. However, along with many advantages, these chainsaws also have some disadvantages. I would like to mention here the pros and cons of this chainsaw model.
User Feedback Regarding Husqvarna 572 XP Problems
I would like to present here the feedback of two users that may help you further understand the problems with this chainsaw model.
A user reported that his Husqvarna 572 XP chainsaw was running great, but suddenly it wouldn’t start. Using a single choke also does not provide any benefit. He took several steps such as replacing the spark plug, and after monitoring the compression, he got good. He is using fresh fuel but is still not starting.
Another user reported that his 572 XP chainsaw bogs out when it warms up. In most cases, this problem occurs after the chainsaw has been running for an hour. After cooling for a while, it runs fine again, but only until it warms up. He always has to face this problem.
Alternative Brands Of Husqvarna 572 XP
I would like to mention three more chainsaw models here that can be an alternative to the Husqvarna 572 XP. Chainsaws have almost the same engine capacity and performance but differ in price.
Alternative 1: Stihl MS 462 C-M
This chainsaw model is one of the best among 70cc chainsaws. The 72.2cc engine of these chainsaws can deliver 6.0 bhp of power. As a result, it is a very popular chainsaw model among loggers. Additionally, the M-Tronic system places them at a unique height.
Alternative 2: ECHO CS-7310P
This chainsaw model has a powerful 73.5 cc engine that will make your work easier. The company has specially designed this chainsaw model for professionals. These chainsaws are available with many useful features, among which the decompression valve feature is outstanding.
Alternative 3: Makita EA7301PRZ
This chainsaw model is quite impressive, coming with a 73 cc engine that produces around 5.4 horsepower. These chainsaws are easier to start and have a more balanced weight. Moreover, these chainsaws are durable as they are made of magnesium.
Frequently Asked Questions
What Is The Weight Of A Husqvarna 572 XP Chainsaw?
The powerhead weight of a Husqvarna 572 XP chainsaw is 14.5 lbs, excluding cutting equipment.
How Many Horsepowers Is a Husqvarna 572 XP?
The Husqvarna 572 XP chainsaw has a 70.46 cc engine that produces 5.8 hp of power.
Is The 572 XP A Good Saw?
Yes, the Husqvarna 572 XP is undoubtedly a good chainsaw. It has all the necessary features to make your work easier.
When Was The Husqvarna 572XP Made?
The company first launched its Husqvarna 572 XP chainsaw model in the market on August 17, 2017.
Is The Husqvarna 572 XP A Pro Saw?
Yes, the Husqvarna 572 XP is a pro chainsaw. You can use it to do all kinds of professional tasks.
Final Declaration
While operating any chainsaw, it is normal for you to experience some minor problems. The Husqvarna 572 XP is a professional chainsaw that rarely causes problems. Yet, users of this model cite some issues that are worth knowing about.
You may not see all the problems I’ve mentioned here with your chainsaw. Still, it’s important to know How to fix these minor problems so you can fix them quickly if they happen to your chainsaw.
If you are a user of the 572 XP model and facing any other issues, let us know through the comment section. I will try to give you a simple solution as soon as possible.
