7 Common Husqvarna 372XP Problems: Things You Should Avoid 

If you’re looking for a high-quality chainsaw, the Husqvarna 372XP is the way to go. This chainsaw model is for professionals and is best for demanding applications.

It is suitable for heavy-duty, handling extra load and high speeds, thanks to the carburetor’s crankshaft, crankcase, and vibration damping.

Undoubtedly, you might not experience any problems with this chainsaw. Nevertheless, you might face some minor issues while using the 372XP. 

Perfection can hardly be achieved, so you might face problems related to spark heating, compressors, lean, etc. These are minor problems, but you must fix them quickly if you don’t want other parts of your chainsaw to get affected. 

This article will highlight a few possible problems with the Husqvarna 372XP, their causes, and solutions. After reading this piece, you will be confident in fixing your chainsaw and returning it to work. 

After the 372 XP problems, causes, and solutions, I will briefly state the chainsaw’s technical specifications and interesting features. All these will give you a better idea of the Husqvarna 372 XP chainsaw.

Husqvarna 372XP Problems and Fixes: Quick Table

Explaining The 7 Husqvarna 372XP and How to Fix them Quickly 

Here, I will discuss the possible problems, causes, and solutions of the Husqvarna 372XP chainsaw in detail. With little knowledge of chainsaws, you can fix your chainsaw by following these quick fixes. 

Problem 1: Heating Issue

This is one of the common problems I faced while using the Husqvarna 371 XP. The chainsaw can experience heating if the piston is extremely hot. The engine will clear up when started and will not rev to its best power. This problem will worsen, and the chainsaw might end up suffocating itself. The 372XP might run on low power whenever the issue comes up. 

Cause:

One of the causes of heating is the carburetor. If fuel does not pass through the Stihl MS 211 c carburetor, the chainsaw will experience frequent heating. A heating spark plug is another cause of heating. If the spark plug ceases to do its job, the 372XP will heat more than usual. 

How To Fix:

To fix this problem, you should be cautious. Take away the carburetor gauze filter to see if the gas is leaking. Before troubleshooting the chainsaw, ensure it cools off. It would do you a lot of good to replace the coil. 

---

Problem 2: Low Compressor

Many people complained about this problem. A few of the common issues a 372XP chainsaw might be exposed to are caused by a low compressor. These problems include expanded cylinders, fewer gasoline pumps, heating, and the inability to start. 

Cause:

The first cause that should come to mind when talking about a low compressor is the cylinder. If the cylinder is faulty, the compressor will be low. Also, running the 372 XP on stale fuel could result in a low compressor. If you pay no attention to the oil, the compressor will fail. 

How To Fix:

Allow the chainsaw to cool down before proceeding with any solution. Two solutions are available for this problem: change the piston to help the compressor reach the desired psi.

Second, replace the cylinder since that may just solve the entire issue. 

---

Problem 3: X Torq

My chainsaw had this torq issue when I used mixed oil. I advise that you refrain from mixing oil when using this chainsaw if you want to avoid running into X torq issues. 

Cause:

My chainsaw had this torq issue when I used mixed oil. I advise that you refrain from mixing oil when using this chainsaw if you want to avoid running into X torq issues. 

How To Fix:

When you think about what caused your X torq problem, think about when you used mixed oil on your chainsaw. You will likely experience the same issue if you use mixed oil on another model or brand of chainsaw. If you did not use mixed oil, then the module of the chainsaw needs to be updated and tested. 

A few things must be replaced to fix this common issue. Consider replacing the Stihl chainsaw ms 211 carburetor, fuel filter, fuel line, and air filter. The saw will only shut down if these things are replaced.

In most cases, returning the saw is best, as they will be able to run a pressure test on it. 

---

Problem 4: Spark Problem

This problem has been constant with chainsaws, and plug changing might not be the solution. I noticed that if a plug sparks outside the conference of the cylinder, it would not spark when compressed during a test. 

Cause:

A broken wire is mostly the cause of a plug that doesn’t ignite, but running on an old coil could also contribute. The sparking problem is typical for chainsaws with new engines. However, the spark plug might be filled with dirt and cause the saw not to come on. A thorough cleaning might be the solution. 

How To Fix:

Luckily, this problem comes with a few working fixes. Replacing the plug might be the solution most of the time. Pouring trim petrol through the cylinder could also fix this problem. In other cases, consider decompressing in and out before cleaning with soapy water and checking for leaks. 

---

Problem 5: Starter Problem

Some customers have complained about this problem. The 372 XP works perfectly fine for some minutes while in use but suddenly begins to die down. Starting the chainsaw after it shuts down could be a struggle.

Cause:

Leakage might be the primary cause of the starting problem, so check the vent system to see if it leaks. The compressor should also be examined to know if it is in good condition. Other possible causes include brittle coils and extreme heating. 

How To Fix:

Install a new piston after heating to make the compressor drop and disable the saw from pumping gasoline. The chainsaw might start again after some time. Replace your brittle coil with a better one. Examine the fuel system before and after the pressure test for clogging. 

---

Problem 6: Troubleshooting Issue

A few users complain of troubleshooting problems. This issue could mess up your plans for the day and cut your work short if not swiftly dealt with. Checking the Stihl ms 211 carb settings is essential.

Cause:

There are several causes of troubleshooting, and some of them include a dirty carburetor, plugged fuel filter, plugged air filter, clogged spark-arrestor screen, and spark plug. 

How To Fix:

To fix the troubleshooting problem, you should inspect your fuel filter because sawdust and other debris could be causing problems. About the dirty carburetor, check out the Stihl ms 211 carburetor kit to figure out the Stihl ms 211 c carb settings. Remove the air filter and apply some carburetor cleaner. 

---

Problem 7: Lean Issue

A running lean is becoming prevalent with chainsaws. It is mainly around the area where the carburetor attaches to the boot. A running lean might be challenging to detect, but when the cause is discovered, fixing it becomes easy.

Cause:

The primary cause of a running lean is the failure of the carburetor to turn towards the proper air. Another cause of the running lean is incorrect fuel mixture. If the air-to-fuel mixture is too light, you might constantly face a running lean. 

How To Fix:

To begin this fix, discover the leaking air, impulse the line location, reconnect the fuel line, and test run. Ensure that your air-to-fuel mixture is balanced; there shouldn’t be too much little air and fuel nor excess fuel and air. 

---

Interesting Features

• X-Torq Engine Technology: The X-Torq engine technology offers a powerful performance while cutting down on fuel use and pollution.
• Air Injection: Removing dust and other contaminants from the air before reaching the engine prolongs engine life.
• Quick Release Air Filter: The quick-release design makes maintenance and cleaning simple and practical.
• Automatic Oil Pump: The automatic oil pump ensures that the bar and chain always have oil available, extending the life of both parts.
• Combination chokes/stop control: This feature makes it simple to start the engine quickly and effortlessly and stop it quickly when necessary.
• Inertia Activated Chain Brake: The inertia-activated chain brake stops the chain if kickback occurs, adding an additional layer of protection.
• LowVib: By lowering vibration levels, this feature makes it more bearable to use for prolonged durations.

Technical Specifications & Interesting Features of Husqvarna 372XP

The fact that the Husqvarna 372 XP chainsaw is among the finest is thanks to its specifications and features. The chainsaw is perfect for professionals who deal with heavy-duty. 

Prevention and Maintenance of Husqvarna 372 XP

Allow me to suggest some recommendations on the ways to take care of a chainsaw for optimal performance and longevity. I will be sharing my daily routine on chainsaw maintenance. Daily maintenance is preferable to weekly and monthly to ensure that the chainsaw functions properly. 

Time has to be dedicated to cleaning regularly, checking for worn-out or rusted parts, bolt tightening, and oiling are vital steps for safety and prevention of malfunctions. Efficiency and speed are assured if the chainsaw is properly maintained. 

Daily Maintenance Plan

• Clean the external surfaces of the chainsaw with a brush or compressed air.
• Wipe the chain break mechanism that is on the interior of the clutch cover.
• Examine the lockout mechanism on the throttle to ensure it is working properly.
• Check for damage on the chain catch to see if replacement is needed.
• Inspect the guide bar to ensure it is free of burs and debris. 
• Clean the lubrication holes on the rear of the guide bar.
• Wipe the groove in the guide bar properly to ensure oil distribution.
• Look at the chain and check for cracks in the rivets and links.
• Check for normal wear, and ensure a correct tension.
• Chain has to be sharp; if not, sharpen it before use.
• Inspect the drive sprocket for excessive wear, and replace it if needed. 
• Clean out the air intake of the starter unit and tighten all screws as you attach the side cover. 
• Ensure that the stop switch works correctly. 
• Check out the engine tank and your fuel lines for any fuel leaks. 

Frequently Asked Questions

Final Thoughts